How To Fix A Broken Fishing Rod? (Easy Steps For Beginner)

Fishing is an incredibly popular pastime. Whether you are an experienced angler or a beginner, knowing how to fix a broken fishing rod is essential for any fisherman.

It can be a daunting task, as there are many different types of rods that can break and need to be fixed.

Fortunately, this article will provide step-by-step instructions on how to repair your broken fishing rod and get back out on the water in no time.

How To Fix A Broken Fishing Rod

Problems With Fishing Rod

Even when anglers are having a good day, they will most often meet an unpleasant fate when they step on their fishing rods.

It is somehow unpleasant, not to be able to manage the cracking rod.

Depending on the severity of the breakage, it is possible to repair damaged line guides, a broken rod tip or a broken ferrule.

However, if a complete break or a complete crack exists along the main shaft of the pole, the damage is likely to be permanent.

Before starting your fixing, at first figure out some type of damages that occur frequently.

1. Broken Rod Tip

A broken rod tip can be a frustrating experience for the angler. The broken piece of the fishing rod can cause problems when casting and hooking fish.

The tip can also become damaged while reeling in a catch, which can lead to an injury.

In most cases, a tip that’s a few millimeters from the end can be repaired without a substantial impact on the integrity of the rod’s performance.

You can expect a minor decrease in sensitivity. Except for extremely picky light biters, this will be pretty much a nonissue.

2. Cracked Ferrule

The area where rod pieces meet at the joint is known as the ferrule. Cracks can form for a variety of reasons, but they usually arise when subjected to too much stress.

Fixing a broken ferrule is hard and should be attempted only by those who are competent.

Cracks measuring more than half of the breadth should not be repaired. Any repairs on larger cracks are unlikely to handle reasonable flexing.

3. Broken Rod Middle

If the rod is broken at middle, then it is a big problem. It can prevent the line from being pulled properly, causing the fisherman to lose fish.

Most of the time the fishing rod is broken at the middle, when the metal support that holds the line together, that breaks.

This often happens when someone accidentally steps on or pulls too hard on the fishing line while it’s in the water.

If this happens while you’re trying to catch a fish, your chances of getting a good catch are greatly reduced.

After you have known about different broken rod problem, now you must think about fixing it. Almost all the broken types can be fixed through the below steps.

Equipment’s Need to Fix the Rod

Some common equipment that are needed to fix the rod, is:

  • A little piece of wood
  • A knife
  • A marker
  • Epoxy glue
  • Sandpaper

How To Fix A Broken Fishing Rod

To fix the broken rod, look at these steps carefully. It will reduce your most of the hassles.

Step-1) Clean the broken parts by your sandpaper. It will remove the residue and create a smoothness

Step-2) Simply, collect some rods from a fishing store or buy from departmental store. Then create a spigot ferrule to connect the broken piece of the rod.

Step 3) Put the spigot ferrule into the broken section, you can make it easy by using butt end. Simply push the spigot ferrule through the rod and place the ferrule in the right place

Step-4) Now, put epoxy/glue over the ferrule that is positioning outside of the rod.

Step-5) Then put another end of the broken rod and simply push it over the ferrule.

Step-6) Now gently rub the joint with sandpaper and keep the rod in dry place to fix properly

Final Words

Fishing is a great way to relax and enjoy nature, but one of the worst feelings is when you break your fishing rod.

The good news is that it can often be repaired with some simple tools and techniques.

In this article, we will discuss how to fix a broken fishing rod so you can get back to enjoying your favorite hobby in no time.

We’ll go over the different types of breaks and what materials you’ll need for each one.